CY-CBL-6P-FAN
CY-CI0/CY-RIO generic fan-out adapter cable.
NB: Don't mix GND and shield! The shield is connected to a slightly thicker black wire than the GND black wire. These are the signal from the controller side. Connect the TX to the camera RX and vice versa.
CY-CBL-6P-PFAN
CY-CI0/CY-RIO generic power and fan-out adapter cable.
Cable for equipment with 12v 5.5x2.1 mm power jack.
-
Marshall mini camera
-
PTZ RS232/422 camera
-
Pan/Tilt heads
CY-CBL-6P-ST-15, CY-CBL-6P-ST-50
CY-CI0/CY-RIO adapter cable with straight mapping.
Cable suitable for the CY-RSBM module.
CY-CBL-6P-PWR
CY-CI0/CY-RIO power cable for low consumption Devices
Use for Tally LED for instance (see LED Assembly Guide).
CY-CBL-DTAP
Power supply cable for CY-CI0/CY-RIO from battery or camera using DTAP connector.
AJA Cable
CY-CBL-6P-AJA-01
CY-CI0/CY-RIO adapter cable AJA Rovocam.
The AJA Rovocam is controlled over RS232 directly at the back of the camera or at the RovoRx units.
Astro Design Cable
CY-CBL-ASTRO-01
CI0/RIO cable for Astro Design 8K camera.
Bradley Cable
CY-CBL-6P-BRADLEY-01
Adapter cable provides power and control to the Bradley Micro L PAN/TILT head. You need a separate cable to connect to your camera (see Marshall and Dreamchip)
Canon Cable
If you don't know, it means you need this: CY-CBL-6P-B4-01
CY-CBL-6P-B4-01 (default)
This cable is used to connect the CY-CI0/CY-RIO to the Canon B4 or Cine Servo lenses.
CY-CBL-6P-CN-REM (advanced robotic)
CIS Cable
CY-CBL-6P-CIS-01
CY-CI0/CY-RIO adapter cable for CIS camera.
Cable for CIS camera with a HR10A connector for power and TRRS audio socket for control:
-
VCC-HD3
-
VCC-HD10ZM
CY-CBL-6P-CIS-02
CY-CI0/CY-RIO adapter cable for CIS and Camera Corps.
This cable provides power and control to the mini-camera from CIS and Camera Corp using a HR10A connector.
DJI Cable
CY-CBL-6P-SBUS-01
Dreamchip Cable
CY-CBL-DREAMCHIP-01 (default)
CY-CI0/CY-RIO adapter cable for Dreamchip camera.
This cable provides power and control to all Dreamchip Mini Camera.
CY-CBL-DREAMCHIP-02 (SSM500)
CY-CI0/CY-RIO adapter cable for Dreamchip DCT-Powercable 350-00011v.
This cable provides RS485 control on all Dreamchip camera with the Dreamchip DCT-Powercable 350-00011v.
CY-CBL-DREAMCHIP-03 (with PT-Head)
This is exactly the same cable as CY-CBL-DREAMCHIP-01 except is is slightly longer and more flexible.
This is the cable you need if you are using a PT-Head with your Dreamchip camera.
Fujinon Cable
If you don't know, it means you need this: CY-CBL-6P-FUJI-02 (+ CY-CBL-6P-B4-01)
CY-CBL-6P-FUJI-01 (discontinued)
Discontinued to to bug in lens when used with handels. Requires a lens firmware upgrade.
CY-CBL-6P-FUJI-02 (default)
Use this cable for all Fujinon lenses (B4 and Cabrio), in conjonction with this cable: CY-CBL-6P-B4-01
CY-CBL-6P-FUJI-03 (advanced robotic)
This cable
-
Camera keeps iris control (directly connected to the camera)
-
CI0/RIO takes control of zoom/focus
-
You can get iris/zoom/focus from the RCP
The connector is pricey and difficult to find. We recommend you build your own cable.
Refer to Pin Assignment table in the document below for cable soldering.
IOI Cable
CY-CBL-6P-IOI-01
CY-CI0/CY-RIO adapter cable for IOI camera.
This cable provides power and control to all IO Industries camera.
LANC Cable
CY-CBL-6P-LANC-03
CY-CI0/CY-RIO adapter cable for LANC controlled cameras or Canon Remote-A port.
This cable provides control over compatible with Sony LANC physical interface:
-
Sony, JVC
-
All Canon camcorders and cameras
-
Blackmagic LANC interface
CY-CBL-6P-LANC-01 (Canon Remote-A) (discontinued)
CY-CI0/CY-RIO adapter cable for LANC camera.
This cable provides control over compatible with Sony LANC physical interface:
-
Sony, JVC
-
All Canon camcorders and cameras
-
Blackmagic LANC interface
The second port is not used
CY-CBL-6P-LANC-02 (Sony LANC) (discontinued)
CY-CI0/CY-RIO LANC adapter for Sony LANC cameras with control pass-through.
With double LANC ports: LANC input for remote control pass-through, camera LANC output. The second port is not used to control a second camera but to connect the zoom/focus handle of a camera like Sony PXW-FS7 which only has a single LANC port. Later cameras like the Sony ILME-FX6 and later have dual LANC ports or the zoom handle connects using other types of connectors so this cable is not necessary anymore.
Marshall Cable
CY-CBL-6P-MARS-02 (new)
CY-CI0/CY-RIO adapter cable for Marshall camera. CY-CBL-6P-MARS-02 replaces CY-CBL-6P-MARS-01i, same pinout but thinner and longer to be work on the small PT head.
This cable provides power and control to a newer Marshall mini camera having 12 pin Hirose connector.
CY-CBL-6P-PFAN (older)
CY-CI0/CY-RIO adapter cable for Marshall camera with power and RS485 Phoenix.
Cable for Marshall mini camera equipped with power DC jack and 2 position RS485 terminal block.
Panasonic Cable
CY-CBL-6P-PAN-10P
CY-CI0/CY-RIO adapter cable for Panasonic camera.
This cable provides control over the older Panasonic P2 camera.
CY-CBL-6P-SONY-XX
CY-CI0/CY-RIO adapter cable for Sony 8-pin remote interface with power.
This cable provides control to Sony professional camera and camcorder through the 8-pin remote interface.
NOTE
The last number of the cable ( -01, -02, etc.) refers to the batch and can vary based on when you order.
Tilta
If you don't know : If you don't know, it means you need this: CY-CBL-TILTA-SERIAL.
Lockable, works with CI0/RIO and provide power+control.
CY-CBL-TILTA-USB
CY-RIO adapter cable for Tilta motors.
Plugs on CY-RIO (USB) and Tilta motors (LEMO). Needs external power supply.
CY-CBL-TILTA-SERIAL
CY-RIO/CY-CI0 adapter cable for Tilta motors.
Toshiba Cable
CY-CBL-6P-TOSHIBA-01
CY-CI0/CY-RIO adapter cable for Toshiba camera.
Cable for Toshiba camera and any RS232 device.
VISCA Cable
CY-CBL-6P-PFAN → VISCA4, VISCA5, VISCA9
CY-CI0/CY-RIO adapter cable with power for VISCA camera using RS422 can be constructed from CY-CBL-6P-PFAN and a 4, 5 or 9 pin 3.5 mm pitch Phoenix connector.
